Installation and maintenance of LED tri-proof lights.

The LED tri-proof light adopts special anti-oxidation and anti-corrosion materials and silicone sealing rings to achieve the protection requirements of the light. The LED tri-proof light performs anti-corrosion, waterproof and anti-oxidation treatments on the circuit control board. Now let me tell you about the installation and maintenance of LED tri-proof lights. Here are some answers.

Here is the content list:

l The installation method of LED tri-proof light.

l Maintenance items of LED tri-proof light.

l The connection method of emergency LED tri-proof light.

The installation method of LED tri-proof light.

There are two ways to install LED tri-proof lights. They are ceiling installation and suspension installation. Ceiling installation According to the installation hole size of the LED tri-proof light, punch the corresponding installation bolt hole at the position where the LED tri-proof light is to be installed, and then install and fix it with bolts. The suspended installation of LED tri-proof lights is mainly suitable for places with very high heights and a wide range of lighting requirements. When installing the LED tri-proof light, fix the lifting adapter plate on the LED tri-proof light with bolts, connect the cable to the LED tri-proof light, and then connect the G3/4 pipe thread of the LED tri-proof light and the standard G3/ 4 pipe threaded wiring steel pipes are screwed together.

Maintenance items of LED tri-proof light.

First, the dust and dirt on the housing and tube of the LED tri-proof light should be cleaned regularly, and pay attention to the water mist in the lamp cavity of the LED tri-proof light used in a humid environment. It should be removed in time to prevent it from appearing for a long time. Corrosion damage or leakage short circuit phenomenon.

Second, check the transparent parts of the LED tri-proof light for signs of foreign body impact, and whether the protective net is loose, desoldering, corrosion, etc. If so, stop using it and repair and replace it in time.

Third, if the light source of the LED tri-proof light is damaged, it should be replaced in time to avoid the long-term abnormal state of the electrical components such as the ballast due to the failure of the light source to start the LED tri-proof light.

Fourth, when turning on the LED tri-proof lampshade, you should cut off the power and open the lid according to the requirements of the warning sign. After opening the cover, check whether the explosion-proof bonding surface of the LED tri-proof light is intact, whether the rubber seal is abnormal, whether the wire insulation layer is green and carbonized, whether the insulation and electrical components are deformed and scorched. If there are such problems, they should be repaired and replaced in time.

Fifth, try not to switch frequently when using LED tri-proof lights. Because the LED tri-proof light is frequently started, the current through the filament is greater than the current during normal operation, which makes the temperature of the filament rise sharply and accelerates sublimation, which will greatly reduce the service life of the LED tri-proof light.

The connection method of emergency LED tri-proof light.

First, connect the circuit strictly following the wiring diagram. Each port of the LED tri-proof light is connected to the following lines in the order: connecting live wire, a neutral wire, light source, drive power, light source, and wall switch line. Note that the wall switch only controls the mains lighting and does not affect the emergency lighting. Finally, the white socket is connected to the battery pack.

Second, the emergency power supply of the LED tri-proof light must not be unloaded. Whether it is to detect the emergency lighting function or the inverter charging function, it must be carried out under the state of the load light source.

Third, the live wire and neutral wire of the LED tri-proof light are directly connected to the main power line, and these two lines are prohibited from being connected to the switch.

Fourth, test whether the battery can be used for emergency lighting. When there is electricity, press and hold the test switch button to switch to emergency lighting.

Fifth, the light source of the LED tri-proof light is not controlled by the switch after the emergency lighting is started.

Our official website is https://www.yuanhui-lighting.com/. If you are engaged in LED tri-proof light-related work or want to learn more about our company, you can communicate with us on the website. Our cost-effective products are well received by everyone.

In addition, we also have products such as LED Ceiling Light and LED Panel Light.